Category: Compressors & Cylinders
There are three ways to fill your PCP airgun:
Hand Pump – Cheapest option but very labour intensive and pump will need regular maintenance. This option will give you a gym workout as it can take several hundred pumps, and each pump is not equal. Good rule is to do 40 pumps at 10 minute intervals and use full upward and downward motions to ensure the pump doesn’t overheat and burn O-rings.
Cylinder – Easy way of filling but will need a fill station to connect cylinder to gun. This option requires you to have your cylinder filled at a Dive/Airgun/ Paintball shop with an adequate compressor capable of filling larger volumes up to 300BAR.
Compressor – The easiest and most convenient way to fill your airgun but also loud & expensive. Takes a few minutes to fill your airgun depending on current pressure and the cylinder capacity of the airgun. 12V/ 220V options available – 12V option can be connected to your cars battery for convenience or connected to normal power. Compressors do require maintenance.
Please note that compressors are ONLY made to fill small cylinders attached to your gun. Compressors get warmer the longer you run them and will get to a point where it overheats and damages the O-rings on your piston. Good rule is to never run your compressor longer than 10 minutes at a time and give it adequate time to cool down before using again to ensure longevity.
In cases where compressors are damaged we do offer a repair service at a cost. (O-ring damage is not a factory fault and wont be repaired under warranty)
As a golden rule never shoot your regulated PCP air gun under the regulator pressure or under 100BAR for non- regulated airguns. This will ensure that no damage is caused to your airgun and filling time will be less.
Showing 1–16 of 90 resultsSorted by latest
-
-
SPARE HIGH PRESSURE HOSE 1/8 BSP – 1/8 BSP
R180.00Add to basketSpare high pressure hose for Pcp fill stations, hand pump or compressor – 1/8″ male BSP x 1/8″ male BSP
-
4.7L CYLINDER BOOTS
R430.00Add to basketThis 4.7l Cylinder boot will keep your cylinder from falling over. The rubber boot simply pushes on to the the bottom of your cylinder and gives a flat base to help prevent the bottle from falling over.
The flat bottoms allow the cylinders to stand upright and are vented with ribs and drain holes to allow water to drain away to help prevent corrosion.
Designed fit perfectly over the bottom of your cylinder, providing superb impact protection and improved stability.
Made from a high quality rubber compound.
-
HIGH PRESSURE PCP HAND PUMP (TITANIUM)
Original price was: R2,850.00.R1,550.00Current price is: R1,550.00.Add to basketHigh-pressure hand pump for filling PCP air rifles and pistols. Ideal for remote areas where scuba cylinder filling is not possible.
Pumps up to 310 bar!
Note:Â The picture is a close representation of the product
The hand pump is not included with any rifle or pistol unless specified
- 3.5 Stage High Pressure Design and High Efficiency: With the exclusive 3.5 stage design, it compresses the maximum amount of air possible from each smooth stroke. That means fewer strokes and less work to fill your air gun. You will also save more power comparing with traditional hand pumps. Test inflating result: Charging 500cc tank from 1000PSI-3000PSI, needs about 350 fills; 200cc Tank from 1000PSI-3000Psi.needs about 140 fills.
- With Oil-Moisture Filter : With the new filter design, it can filter above 90% of moisture. So you can feel free to inflate your scuba diving tank without moisture air. When the blue desiccant become red as enough water, you can pour them out for drying by referring to the user manual.
- Durable Quality and Durable Performance: With the high quality stainless steel pump body and rubber handle, wide and strong base plate, it can ensure more stable and long-lasting using life. It can bear over 15000 times of tear and wear. At the 200 bar pressure, you can continuously use the pump more than 2 hours.
- Specifications: General Output nut: M10*1 (not G1/8) , 8mm wide use quick connector, Max pressure : 310 bar or 4500 psi, Light weight 3.1 kg, Portable size: length 62cm/24.5inch closed, 105cm/41.3inch open
- What You Get: Hand Pump, user manual, accessory kit
-
CONVERSION KIT – BOTTLE RIFLE TO BUPPLUP – FOR AVENGE-X
R830.00Add to basketAvenge-X Conversion Kit: Bottle Rifle to Bullpup
PLEASE NOTE!!!!!
You need the following stock to complete the conversion:
AVENGE-X WOODEN BULLPUP STOCK COMPLETE FOR BOTTLE MODEL (P-NV-AX/WBBS)
Failure to do so will result in half parts to be assembled.
-
-
500CC CARBON FIBER BOTTLE FOR NOVA VISTA AVENGE-X 300BAR WITH VALVE P-NV-AX/AV AS A COMBO
R4,120.00Add to basketIntroducing the ultimate 500cc 300 Bar carbon fiber bottle with valve for the Nova Vista Avenge-X range. Increase your shot count and elevate your shooting experience!
0.5L:
outside diameter: 48.5mm
length: 428mm
weight: 0.48kg
thread: M18-18UNF
300 BAR WORKING PRESSURE
-
450CC CARBON FIBER BOTTLE FOR NOVA VISTA AVENGE-X, 300 BAR WITH VALVE P-NV-AX/AV AS A COMBO
R3,670.00Add to basketEnhance your Nova Vista Avenge-X with this carbon fiber bottle combo. With a working pressure of 300 BAR, this 0.45L bottle is lightweight and durable.
0.45L:
outside diameter: 48.5mm
length: 393mm
weight: 0.44kg
thread: M18-18UNF
300 BAR WORKING PRESSURE
